Search results

  1. M

    Stampede RT-590 3RPM Auger Upgrade

    So I should probably look into getting a 3RPM auger motor then? Based on what I’ve read here that’s what the newer ones have.
  2. M

    Stampede RT-590 3RPM Auger Upgrade

    Do you know what year the “before” and “after were? Mine is about 4-4.5 years old. Just acquired it and haven’t run it yet. Waiting on some parts before I start it up. Just curious if I should buy the faster auger if mine may have the slower one.
  3. M

    Stampede All weather smoke vents

    How old is your 590? If not in use willing to part with it?
  4. M

    Stampede All-Weather Smoke Vents

    Yeah overtime. Just bought a used 590 and I work for a mechanical company and have a guy in our metal shop making a stainless rain guard for it. But I like how these look they just seemed chincy. Still undecided what way I’ll go. I’ll have to drill holes for the rain guard these I won’t.
  5. M

    Stampede RT-590 3RPM Auger Upgrade

    How did you confirm what rpm it was? I bought my 590 used and want to know what it’s got. Just acquired it couple weeks back. It is about 4-4.5 years old
  6. M

    Stampede RT-590 3RPM Auger Upgrade

    Where did I miss the link? Wanting to get the 2rpm or like your asking the 2.5 for my 590
  7. M

    Bull Any luck on 2.5 Auger for 2022 with Recteq?

    From what I understand the 590 uses the same controller as the 1250. Could I run a true 2rpm on the 590 or has anyone tried it?
  8. M

    Stampede All-Weather Smoke Vents

    How long did this last?
  9. M

    Stampede All weather smoke vents

    How well did this hold up. Your Post is a few years old just curious. Thanks.
  10. M

    Stampede Sealing the RT-590 Lid

    I did try that. Didn’t work. It’s actually not bent properly. Putting a miter gauge on it the bottom is true 45 degree and the top is less. More like 38-42. Causing the top to travel downward to the top of the grill when flat on the bottom. Oh well I’ll gasket both the lid and the barrel side...
  11. M

    Stampede Sealing the RT-590 Lid

    Just contacted them about a new lid cause mine is not bent properly from factory. My problem is I bought it second hand. I mentioned trying to seal the lid tk them and they said no don’t. I kept the gasket is causing it to not seal. I clearly used and angle finder and it’s not a 45 degree angle...
  12. M

    Bull To seal or not to seal

    If if they replaced it for free I’d be a life time customer that’s a fact. But I doubt it.
  13. M

    Bull To seal or not to seal

    Well I’ve yet to use I have bought it second hand. Hoping to try to get this all resolved before using it. Still have my bullseye! But for now been messing with the lid for days. Cut little shims filled out the holes had lid support made at sheet metal shop I work for ect.. been a pain in the...
  14. M

    Bull To seal or not to seal

    You are correct the lid is not the correct angle. I am the second owner of the unit so I doubt they’ll send me a lid. I’ll reach out but the top portion needs to be opened up a little. Afraid if I try I’ll crack the porcelain paint and it’ll be ruined.
  15. M

    Stampede Sealing the RT-590 Lid

    Was your lid formed good to the smoker? Bought a second hand 590 and trying to seal the lid. Not much luck as the bends aren’t excatly 45s. Original owner didn’t seal it and took me forever to clean it up. Was hoping to keep it clean for years to come. Afraid to try and bend it as it might mess...
  16. M

    Show us what you're cooking...

    Maybe didn’t let the fully load?
  17. M

    Bull To seal or not to seal

    Yeah. I even elongated the holes front to back and shimmed the hinges with 14g material. My lid touches at the back and not in the front corner like shown. I do have some sag. I had my work make a support bracket to go under the lid supports and will drill and bolt it to raise the sag. Need to...
  18. M

    Bull To seal or not to seal

    I’ll have to make the elongated holes longer for proper adjustment.
  19. M

    Bull To seal or not to seal

    Oh I have loosened added shims and tried all sorts of methods. Other than elongating the holes tk move the lid further than factory settings allowed. This is my result at max forward and with a 14 gauge SS shim under hinges.
  20. M

    Bull To seal or not to seal

    I need someone with a 590 to chime in. I did the main barrel and it doesn’t seal all the way. Since it’s a hexagon the center section basically not matching corner to corner now. Center section of the lid since it’s 3 sides of the hexagon. If that makes sense. Now I have to scrape all this off...
Back
Top